How To Set Ip Address In Windows Xp

How to configure wired TCP/IP Properties of my computer(Windows XP,Vista,seven,8,x,Mac)?

Step 1.ClickCommencement->Control Panel->select and double click Network and internet connections (If you can´t find it, please go next) ->select and double click Network Connections.

Step ii.Highlight and correct-click theLocal Area Connection icon; click onCondition and go toGeneral . Click theProperties push button to open up the properties window.

Step 3. Highlight theCyberspace Protocol (TCP/IP)tab, and and so double click information technology or clickProperties. The TCP/IP Properties window will brandish.

Step 4 .Now you lot have two ways to configure the TCP/IP protocol beneath:

1. Assigned past DHCP Sever

SelectObtain an IP address automatically andObtain DNS Server address automatically, as shown in the effigy below. These may be selected by default. Then clickOK to save setting.

2.Assigned manually

1) SelectUtilise the following IP address, equally shown in the following effigy.

If the router's LAN IP address is 192.168.1.1, please type in IP address 192.168.1.x （x is from two to 253）, subnet mask 255.255.255.0, and default gateway 192.168.1.1.

2) SelectUtilize the post-obit DNS server addresses, as shown in the following figure. And so type the DNS server IP address, which should be provided by your ISP. Finally, remember to clickOK to save settings.

Note: In near cases, type your local expanse DNS server IP addresses into it. The Preferred DNS server is the same as the default gateway. For the Secondary DNS server, you lot could leave it blank or type in eight.8.8.8.

Pace 5. ClickOKto save and utilise your settings.

For Windows Vista&7

Step1. ClickStart ->Control Panel ->Network and Internet -> Network and Sharing Eye.

Step2. In the task list, delight clickManage network connections (for Windows Vista )/Modify adapter settings (for Windows7 ) .

Highlight and right-click theLocal Area Connection icon and select Properties.

Step 3.SelectNet Protocol Version four(TCP/IPv4), double click it or clickBackdrop.

Step 4. In that location are two ways to configure the TCP/IP Properties, Assigned by DHCP server automatically ormanually.

i. Assigned by DHCP server

SelectObtain an IP address automatically andObtain DNS server accost automatically. If necessary, then clickOK to save the settings.

2. Assigned manually

one) SelectUse the following IP address, type the IP accost, subnet mask, and default gateway IP address into information technology.

If the router's LAN IP address is 192.168.1.i, delight type in IP accost 192.168.1.x （x is from 2 to 253）, subnet mask 255.255.255.0, and default gateway 192.168.1.ane.

2) SelectUse the following DNS server addresses, as shown in the post-obit figure. And then type the DNS server IP accost, which should be provided by your Internet service provider. If necessary, and then clickOK to save the settings.

Notation: In most cases, blazon your local area DNS server IP addresses into it.

The Preferred DNS server is the same as the default gateway. For the Secondary DNS server, you could exit it blank or type in 8.8.8.viii.

Step 5 ClickOKto relieve and apply your settings.

For Windows 8&8.1

Step1.Go toControl Panel. Here we will illustrate different ways to observe a control panel on Windows 8.

Press "Windowscentral +F ", a search box will come out, please input thecontrol panel and press enter;
Press "Windowskey+ R", then at that place will be a "run" box, inputcommand panel, and press enter;
Printing "Windowsfundamental +Ten", and click on "command panel";
You can also input "command panel" in the search bar on the right-paw side of the screen.

Footstep ii.In Category view click on Network and Internet

Stride three.Click on Network and Sharing Centre

Step iv.Click on Change Adapter Settings

Stride 5.Right-click on Local Expanse Connexion and click Properties

Step 6. Click Internet Protocol Version 4 (TCP/IP) and then click Properties

Step 7.Change to Utilise the post-obit IP accost and input your IP and DNS information.

Stride 8.Click OK to save and utilize your settings.

For Windows 10

Footstep 1.Go to Control Panel. Press Windows cardinal + X at the aforementioned time and selectControl Console.

Step2. Click onNetwork and Internet ->Network and Sharing Center, click on Alter adapter settings on the left side .

Step 3. Highlight and right-click onEthernet, then selectProperties.

Step 4. Double-click onInternet Protocol Version 4 or click Properties.

Stride v.There are two means to configure the TCP/IP Properties, Assigned by DHCP server automatically ormanually.

1. Assigned by DHCP server

SelectObtain an IP address automatically andObtain DNS server accost automatically. If necessary, then clickOK to save the settings.

2. Assigned manually

1) SelectUse the post-obit IP address, type IP address, subnet mask and default gateway IP address into it.

If the router'due south LAN IP address is 192.168.i.one, please type in IP address 192.168.1.10 （x is from ii to 253）, subnet mask 255.255.255.0, and default gateway 192.168.1.i.

ii) SelectUse the following DNS server addresses, as shown in the post-obit figure. And and so type the DNS server IP accost, which should be provided by your ISP. If necessary, and then clickOK to salvage the settings.

Note: In virtually cases, type your local surface area DNS server IP addresses into it.

The Preferred DNS server is the same every bit to default gateway. For the Secondary DNS server, you could get out it blank or type in eight.8.8.8.

Footstep 6.ClickOKto save and employ your settings.

For Mac Os

Pace i. Click theApple tree icon, from theApple tree driblet-downward listing, selectSystem Preferences.

Step 2 Click theNetwork icon.

Step 3 In the left column, selectEthernet. Click on the Configure IPv4 field, and select 'Manually"

Pace 4.Input your IP information (Router is the Default Gateway address) and click Apply.

Note:

1.DNS server should exist provided by your Internet access provider. Please contact your ISP to bank check them.

two.In most cases, you could blazon your local area DNS server IP addresses into information technology. The DNS server is the same every bit the Router LAN IP address. In some cases, you could also leave it blank or type in eight.eight.8.8.

Become to know more than details of each office and configuration please get to Download Middle to download the manual of your product.

Is this faq useful?

Your feedback helps meliorate this site.